Thank you! I will get them.
-
The Fedora Lounge is supported in part by commission earning affiliate links sitewide. Please support us by using them. You may learn more here.
Photos of hatters tools
- Thread starter airforceindy
- Start date
Thank you! I will get them.
Thanks Óle! Casters w/o swivels - got it!
Mr.Astor
Banned
- Messages
- 246
- Location
- New Jersey
John, nothing on his etsy site, just a message under construction with what looks like a drawing of the Hindenburg!
Block Maker
New in Town
- Messages
- 34
- Location
- mid west
No worries…can't blame a guy for trying!
TheDane
Call Me a Cab
- Messages
- 2,670
- Location
- Copenhagen, Denmark
Of course ... caster wheels! Thanks John! Maybe we should rename them "castor" wheels for this purpose
Gentlemen and ladies, Dylan's email address is: [email protected], and he has authorized me to share it with you. He's advised me he's going to be away from home for a week and plans to start stitch awl production when he returns.
The time is ripe.
Last edited:
Of course ... caster wheels! Thanks John! Maybe we should rename them "castor" wheels for this purpose
;-)
Featured products
-
John Lofgren Monkey Boots Shinki Horsebuttt - $1,136 The classic monkey boot silhouette in an incredibly rich Shinki russet horse leather. -
Grant Stone Diesel Boot Dark Olive Chromexcel - $395 Goodyear welted, Horween Chromexcel, classic good looks. -
Schott 568 Vandals Jacket - $1,250 The classic Perfecto motorcycle jacket, in a very special limited-edition Schott double rider style.
Block Maker
New in Town
- Messages
- 34
- Location
- mid west
Mine was ordered last week….if it works 1/2 as good as it looks…it will be leaps and bounds over the one I have now!
Check these out on eBay. I bought them. 500 should last me until I retire from my present career & become a real hatter ;-)
http://bit.ly/1jvaRh6
Here's one I found advertised as a tip stand after a lot of searching. The dimensions look a lot closer. Your thoughts?
Hatter4
One of the Regulars
- Messages
- 224
- Location
- East Petersburg, PA
John: Again, from my collection is the Handy Hatter and two bottles of Luton's straw dye--not quite the same as the one you showed. Also, as far as the tip stand is concerned, it could be a tip stand by a different manufacturer but I always thought that the piece that goes inside the hat should be wider so you could iron the top of the hat.
Hatter4
One of the Regulars
- Messages
- 224
- Location
- East Petersburg, PA
Someone a while back asked for a photograph of a flange stand. Here is one I have--they also made them in open-sided versions. Hope this helps.
Hatter4
One of the Regulars
- Messages
- 224
- Location
- East Petersburg, PA
John, On page 60 post#593 you show a page from HSH of a curling board and there bottom board. I have both, and a smaller curling board also
ManofKent
My Mail is Forwarded Here
- Messages
- 3,039
- Location
- United Kingdom
Great packaging on those dyes and 'Handy Hatter' - thanks both for sharing them.
Luton is still the straw hat making centre for the UK, presumably that's why the 'Luton' dyes were named that way...
Luton is still the straw hat making centre for the UK, presumably that's why the 'Luton' dyes were named that way...
Hatter4
One of the Regulars
- Messages
- 224
- Location
- East Petersburg, PA
ManoKent I have a book called "Luton and the hat industy" by Charles Freeman printed in 1976.
Hatter4, I love your posts! Here is an open style flange stand. This was purchased from a man whose grandfather and father were both hatters, and who grew up helping out in his father's shop. The stand is a George Bros., purchased by the grandfather for his son in 1951 as part of the startup investment in the latter's shop.
Hatter4
One of the Regulars
- Messages
- 224
- Location
- East Petersburg, PA
These are called edge irons. Left to right - first one has no manufacturer's mark but it says 1/4" edge; the middle one "Drake Engineering Co. 3/16" edge; and the right one is manufactured by M. Mirren, NY - 1/8" by 3/16".The other photo is a side view of the middle one.
Similar threads
